04/01/2022 - v1.4.0 Release update for XDP Designer GUI
      
      - Added Features:
            - Added programing for total current limit 
            - Display phase count for different power states
            - Use Index values to enter AVP BW and FATR frequencies.
            - Added McKinley rev D FATR ATRH feature
            - Added NVIDIA security panel and VID table steps
      - OTP and config file handling:
            - Added prompt for registers that require "write to OTP and reset" to take effect.
            - Automatic default config file loading in offline mode
            - Added .mic file programming support
      - Bug fixes:
            - Fixed PMBus VOUT_CAL_OFFSET
            - Corrected phase current reporting calculation
            - Fixed inadvertent register changes when navigating to Multi-function pin panel
            - Multi-function generic fault panel improvements
            - Improved parameter setting when using SVID reg map
            - Psys product ID overwrite issue
            - Performance enhancement to regulation and SVID response when operating in single loop
            - Fixed OTP auto write when using "write" in basic settings in PMBus mode
      - Device support:
            - Added Rainier rev B support



02/03/2022 - v1.3.0 Release update for XDP Designer GUI
	
	- Improvements to PWM Firing Order screen graphics to allow users randomly select phases to set up each output.
	- Added Power Stage Type selection feature to McKinley, and Yosemite.
	- Added support for phase by phase enable of the 2x Power Stage capability for Yosemite.
	- Multi Function Pins Panel has Expand All/ Collapse All Buttons to expand or collapse all the pins.	
	- Added IMON Settings panel for NVIDIA
	- Improvements to Load Model Dialog.
	- Fix for OTP Size reporting
	- Bug Fix and Improvements for Malibu, McKinley, Rainier and Yosemite
	- Dongle Firmware version updated to 59.27 to detect AVS Controller
	- General overall GUI improvements

11/24/2021 - v1.2.0 Release update for XDP Designer GUI
	- McKinley Rev D support
	- Added Dell Settings design tool
	- Rev C to Rev D config file converter
	- Updated SVI3 register descriptions
	- Yosemite NVIDIA, AVSBus support (BETA)
	- Malibu Improvements
	- General overall GUI improvements

08/31/2021 - v1.1.1 Release update for XDP Designer GUI
	- The FATR design tool now has same settings of v1.0.0

08/23/2021 - v1.1.0 Release update for XDP Designer GUI

	- Malibu support has been added into the GUI.
	- Added SVI3 Settings panel to make all SVI3 commands available in a single panel.
	- Fixed export issue with Config comparator
	- Allowed writing a value into the register box in the register map page along with changing the values via '+' and '-' button.
	- Removed old revision and non-existent devices from offline pull down list
	- Changes made to show/hide customer specific PMBus commands.
	- Updates to the Config file comparison utility to cover the partial and multi-config file cases.
	- Dongle version updated to 59.24
	- Fixed  defects found with the following design tools
		- Multi Function pin
		- Generic Faults
		- SVI3 design tool panels


07/05/2021 - Initial release of XDP Designer GUI (v1.0.0)
			
	
	- This GUI has support for McKinley and Rainier parts.
	- Has various features/design tools to configure/fine tune the controller. 
		- Config File Load/Save
		- Config File Comparator 
		- Config File Converter 
		- Register Map
		- PMBus Commands
		- Device Programmer
		- Firmware Patch
		- Dongle FW Update
		- OTP Tools
		- Offline Design
		- PID Panel/Load Model
		- Telemetry/ Fault Status
		- Multi Image Config (MIC) file creation utility
		- Tuning Design Tools
			- Basic Controller Settings
			- Device Communication Settings Panels
			- Device Settings
			- Control Loop & Transient Settings Panels
			- Sense & Telemetry Calibration Panels
			- Fault and Protection Panels